index
{ width=600 }
此宏允许更改活动的SOLIDWORKS文档(零件或装配)的单位。
配置宏的常量以指定目标单位系统
Const UNIT_SYSTEM As Integer = swUnitSystem_e.swUnitSystem_Custom '根据下面的常量分别设置自定义单位
Const CUSTOM_LENGTH_UNIT As Integer = swLengthUnit_e.swMETER
Const CUSTOM_ANGLE_UNIT As Integer = swAngleUnit_e.swDEGREES
Const CUSTOM_MASS_UNIT As Integer = swUnitsMassPropMass_e.swUnitsMassPropMass_Pounds
Const CUSTOM_VOLUME_UNIT As Integer = swUnitsMassPropVolume_e.swUnitsMassPropVolume_Feet3
Const CUSTOM_TIME_UNIT As Integer = swUnitsTimeUnit_e.swUnitsTimeUnit_Second
如果UNIT_SYSTEM常量设置为swUnitSystem_e.swUnitSystem_Custom,则需要通过更改CUSTOM_???常量来提供每个自定义类型的单位。
Const UNIT_SYSTEM As Integer = swUnitSystem_e.swUnitSystem_IPS
Const CUSTOM_LENGTH_UNIT As Integer = swLengthUnit_e.swINCHES
Const CUSTOM_ANGLE_UNIT As Integer = swAngleUnit_e.swRADIANS
Const CUSTOM_MASS_UNIT As Integer = swUnitsMassPropMass_e.swUnitsMassPropMass_Kilograms
Const CUSTOM_VOLUME_UNIT As Integer = swUnitsMassPropVolume_e.swUnitsMassPropVolume_Meters3
Const CUSTOM_TIME_UNIT As Integer = swUnitsTimeUnit_e.swUnitsTimeUnit_Minute
Dim swApp As SldWorks.SldWorks
Sub main()
Set swApp = Application.SldWorks
Dim swModel As SldWorks.ModelDoc2
Set swModel = swApp.ActiveDoc
If Not swModel Is Nothing Then
swModel.Extension.SetUserPreferenceInteger swUserPreferenceIntegerValue_e.swUnitSystem, swUserPreferenceOption_e.swDetailingNoOptionSpecified, UNIT_SYSTEM
If UNIT_SYSTEM = swUnitSystem_e.swUnitSystem_Custom Then
swModel.Extension.SetUserPreferenceInteger swUserPreferenceIntegerValue_e.swUnitsLinear, swUserPreferenceOption_e.swDetailingNoOptionSpecified, CUSTOM_LENGTH_UNIT
swModel.Extension.SetUserPreferenceInteger swUserPreferenceIntegerValue_e.swUnitsDualLinear, swUserPreferenceOption_e.swDetailingNoOptionSpecified, CUSTOM_LENGTH_UNIT
swModel.Extension.SetUserPreferenceInteger swUserPreferenceIntegerValue_e.swUnitsAngular, swUserPreferenceOption_e.swDetailingNoOptionSpecified, CUSTOM_ANGLE_UNIT
swModel.Extension.SetUserPreferenceInteger swUserPreferenceIntegerValue_e.swUnitsMassPropLength, swUserPreferenceOption_e.swDetailingNoOptionSpecified, CUSTOM_LENGTH_UNIT
swModel.Extension.SetUserPreferenceInteger swUserPreferenceIntegerValue_e.swUnitsMassPropMass, swUserPreferenceOption_e.swDetailingNoOptionSpecified, CUSTOM_MASS_UNIT
swModel.Extension.SetUserPreferenceInteger swUserPreferenceIntegerValue_e.swUnitsMassPropVolume, swUserPreferenceOption_e.swDetailingNoOptionSpecified, CUSTOM_VOLUME_UNIT
swModel.Extension.SetUserPreferenceInteger swUserPreferenceIntegerValue_e.swUnitsTimeUnits, swUserPreferenceOption_e.swDetailingNoOptionSpecified, CUSTOM_TIME_UNIT
End If
Else
Err.Raise vbError, "", "未打开模型"
End If
End Sub